DIY Pallet Love Project #2--The Bookshelf

And so my love of the humble skid/pallet continues.  Yes, this IS a bathroom that we put a bookshelf in.  Don't try to tell me you never read in the bathroom.  It's quiet in there.

But our bathroom was really boring:  It needed some creative decor.  (This thought only dawned on me after visiting a friends' place, needing to use the bathroom, and finding myself in the coolest, craziest, most whimsical bathroom ever--and wondering why didn't I think of that?  It's a bathroom, people, why not have fun with it???  

So this is really only the beginning...

This pallet project was really simple.

See the curve in the wood on the top image?  They cut those curves into the back of the side supports on the pallets--don't ask me why--but most pallets have those curved notches.  So all I did here was cut the top of the pallet off to the height that I wanted the back of the bookshelf.  What you are looking at is the pallet turned backwards.  I didn't even try to re-space the slats that became the back of the bookshelf--I liked the wonky way they were nailed into place.  I did, however, add screws just to hold everything together better.  I couldn't fit the whole width of the pallet into where I wanted too hang the shelf, so I cut it in half just past  the middle supports.  I pulled off one extra piece of wood and cut it to fit the bottom and screwed it into place.  

I used the top of the back skid--see the uneven and mis-coloured slats?

In it's raw and splintery state, I grabbed an old can of white latex paint--it was actually primer--and barely touched a paintbrush to paint, brushed most of the paint back off on a scrap of wood, then "dry-brushed" a bit more patina onto the pallet bookshelf.  I basically whitewashed it very lightly.  I didn't want to cover the existing patina  of the wood, I just wanted MORE patina.  

This was such a small project that I sanded it by hand.  I just sanded it enough to take all the rough splinters off and round down the worst spots.  I did not sand it until it was perfect.  The sanding helped to make the paint look like it had always been there, too. 

And then I added a latex clear-coat (yep, more of that Benjamin Moore Stays Clear--that single pint can has been used in more projects around here...)--2 coats of it with a very light sanding in between coats with a sanding sponge (you could use 000 steel wool).

And that was it.  Used 2 wall plugs to hang it.

Done.

And yes, that was what I was reading at the time of the bookshelf photos.  

DIY Pallet-Love Project #1: The Shoe Rack

Are you on Pinterest?  I am, finally.  I'm actually on it twice--first as My Primal Adventures, and second as Paleo Toronto.  The two accounts have totally different angles, though, just like how the MPA blog, and the PT website, have totally different purposes.  Check them both out, and feel free to suggest things for me, because being new on both, I haven't pinned very much so far.

Along that note, though, if you check out the MPA boards, you'll see I have a pin-board dedicated to DIY projects, and I've pinned a whole bunch of ideas for re-purposing wooden pallets.  I LOVE all the ideas that are out there.  Old pallets have this amazing patina to them that remind me of reclaimed barn-board or old milk crates.  I've found pallets made from soft woods, sure, but I've also found pallets made with maple, cedar and oak.  It is important to know, though, that they treat pallets with chemicals to keep them from rotting.  Kind-of like how they pressure-treat wood for fences and decks, but without the green hue.  These are pretty ugly chemicals, so I highly recommend doing any sanding of this wood in a well-ventilated area or using a dust mask.  Wash your hands after sanding.  And clear-coat the entire project when complete with a water-based urethane product to seal it in  (I'm a huge fan of Benjamin Moore's Stays Clear; it was used on every gym floor throughout the Toronto School Board--this stuff is tough, dries in about an hour, and barely has any odor whatsoever).

I also happen to love reno projects and making stuff myself.  My hubby and I have this beautiful dining room table idea we've fully drawn plans to build, but I want to make it from Douglas Fir which is not a common wood in Ontario (unless you have a really old barn to tear down) so we haven't been able to get out and get the lumber to make it.  But at some point, that will happen.  And until then, I'm building some of these weekend projects using pallets that I can get hold of for free (which fits my budget perfectly).

So, the pallet in the front is the one I chose for the shoe rack.  It doesn't have a nice patina at all, but that doesn't matter if its going in the closet.  I think it's actually spruce, so it's pretty crappy lumber, but the width of the slats and the spacing between them was already perfect.

This is such a simple and genius project.  We measured the space we had in the closet, decided we didn't want the shoe rack to go up above where the coats hung, and cut the top off to the right height.  We used a skilsaw for this.  Then I dragged it out onto my driveway and used a palm-sander with 80-grit paper and sanded all the rough fronts of the slats, the ends, and got between the slats as best as I could.  I didn't want rough splinters marking anyone's shoes.  I took a sanding sponge to it after that, just to get between the slats a little bit better.  It wasn't perfect, not by any means, but it was better than it was before.

Now, it was a bone-chilling 2 degrees Celsius outside and I was just freezing my @$$ off outside, so I dragged the whole thing into my front hallway to seal it with the clear coat (and hopefully seal in some more of the rough edges). Like I said, the Stays Clear has almost no smell whatsoever and dries fast, so why not?

Two coats of Stays Clear (with a light sanding between coats), and the project was done.  It took less than a half day.  My cost?  $4 for more wall plugs to mount it in the back of the closet.  We were out of them.

Voila!